CornerStone 100 GeoGrid Wall

Creating a CornerStone® reinforced retaining wall system, involves the use of geogrids for reinforcement. CornerStone® walls 4.0ft (1.2m) and taller will automatically have active pressures because of their height. Retaining walls smaller than 4.0ft (1.2m) may also require geogrid reinforcement depending on other related factors. Parking lots, roadways, or positive slopes above walls for example, require the use of reinforcement to help resist the increased pressure behind the wall. Geogrid used with the appropriate lengths, layers, and compacted backfill materials will resist these active forces above and behind the wall. For CornerStone 100 geogrid wall  4.0 ft and taller a qualified engineer should be consulted.

separator-fancy

Step 1: Planning Your Retaining Wall

  • Excavate and prepare Sub Base Leveling Trench 6″ below first course
  • Leveling Pad Trench is approximately
    2.5′ to 3′ wide
  • Normal wall Burial Depth or Embedment Depth is 6″ to 12″ or one block (for more information refer to design manual)
  • Excavate cut line to a 2 to 1 slope or greater
  • Back of wall excavation depth into the bank at the base of the wall should be from the face of wall to the designed length of Geogrid

cornerstone-100-geogrid-wall-step1

Step 2: Cut Geogrid

  • Cut Geogrid Reinforcement to the length specified in the design
  • Geogrids are manufactured in two directions Uni-axial or Bi-axial. Uni-axial grid has one direction of strength and that direction has
    to be oriented perpendicularly to the face
    of the wall during installation. Bi-axial grid
    can be laid in two directions, perpendicular
    and lengthwise to the face of wall (ensure that the lengthwise direction is still in accordance to the length specified by
    the Engineer’s design)
  • Correct geogrid orientation, strength and length is crucial to the success
    of the wall project
  • Each geogrid length should be laid parallel and adjacent to each other but never overlapping

cornerstone-100-geogrid-wall-step2a

cornerstone-100-geogrid-wall-step2b

Step 3: Lay Geogrid

  • Place the geogrid as far forward on the CornerStone® units as possible without revealing it on the face
  • Place the next course of CornerStone®
    units on top of the lower units and
    geogrid at a half bond
  • The two SecureLugs will fit securely into the hollow cores of the two units below and lock the geogrid into the gravel core
  • Pull the unit forward to engage and align
    the SecureLugs
  • Complete the installation of units on the Geogrid Reinforced courses
  • Make sure each unit is installed against the next unit leaving no gaps between unit joints
  • Tension the geogrid in such a way as NOT to disturb the alignment of the upper units
  • Use stakes or backfill materials to maintain the tension during backfilling
  • Do not drive equipment directly on
    top of geogrid

cornerstone-100-geogrid-wall-step3a cornerstone-100-geogrid-wall-step3b

Step 4: Reinforced Backfill

  • Backfill and Compact the Reinforced Zone by placing materials from the back of
    the wall towards the end of the geogrid
  • Install drainage gravel in the cores and 6″ to 12″ behind the units after placing and compacting backfill materials
  • Install and compact backfill materials in 8″ Lifts until wall is complete

cornerstone-100-geogrid-wall-step4a cornerstone-100-geogrid-wall-step4b

More CornerStone 100 Installation

  • cornerstone 100 gravity retaining wall

CornerStone 100 Gravity Retaining Wall Installation

January 7th, 2016|0 Comments

Gravity (SRW) segmental retaining wall systems are structures lower in height that use the CornerStone® unit weight combined with gravel core infill t [...]

  • cornerstone 100 base elevation

CornerStone Retaining Wall Block Base Elevation Change

January 7th, 2016|0 Comments

CornerStone Retaining Wall Block Installation For Base Elevation Change are often required and can be problematic if not planned properly. Correct con [...]

  • cornerstone 100 curved retaining wall

CornerStone 100 Curves

January 7th, 2016|0 Comments

Curve details are often required for specific sites and can be specified by designers and engineers. Correct construction and professional completion [...]

  • cornerstone 100 retaining wall corners

Retaining Wall Corner Installation

January 7th, 2016|0 Comments

Retaining wall corner installation details are often required for specific sites and can be specified by designers and engineers. Correct construction [...]

  • cornerstone 100 stone stairs

CornerStone 100 Stairs

January 7th, 2016|0 Comments

Proper installation of stairs in a wall project requires the same care and thoroughness as the creation of the wall itself. CornerStone’s design featu [...]

  • cornerstone 100 stone pillars

CornerStone 100 Pillars

January 7th, 2016|0 Comments

Pillars add a finishing touch of elegance to any CornerStone® wall project. They can be used to create distinguished entranceways to any residence or [...]

 

By | 2017-04-08T01:06:17+00:00 January 7th, 2016|CornerStone 100, Geogrid Wall, How To, Installation|